Material / Trade Name: MerLube Quick-Kut

Emergency Telephone:  330-666-8609

SECTION 2- INGREDIENT

Specific information is considered as a trade secret and is withheld per CEF 1910:1200 (h). Medical

personnel requiring this information should contact J.J. Merlin Systems with their request per CFR 1010:1200 (h).

SECTION 3- PHYSICAL DATA

Boiling Point, 760 mm Hg: n/a Volatiles, % by Volume: n/a

Specific Gravity (H₂ O=1): 0.92 Solubility in H₂ O, % by Volume: Insoluble

Vapor Pressure, mm Hg: n/a Evaporation Rate, Butyl Acetate=1: n/a

Vapor Density, Air=1: n/a

Appearance and Odor: light amber liquid with faint fatty odor

SECTION 4- FIRE AND EXPLOSION DATA

Flash Point (Method Used): LEL: n/a UEL: n/a

315^o C min. (Cleveland Open Cup)

Flammability Limits: n/a

Extinguishing Media: Dry Chemical, foam, halon. CO2, water spray (fog). Water stream may splash burning liquid and spread fire.

Special Fire Fighting Procedures: Combustible liquid. Use air supplied equipment for fighting interior fires. Cool fire exposed containers with water.

Unusual Fire Explosion Hazards: None

SECTION 5- REACTIVITY DATA

Stability Hazardous Polymerization

__X__ Stable ____ Unstable ____ May Occur __X__ Will Not Occur

Conditions and Materials to Avoid: Strong oxidizing agents.

Hazardous Decomposition Products: Combustion produces carbon monoxide and carbon dioxide along

with thick smoke.

SECTION 6- OCCUPATIONAL EXPOSURE LIMITS

No TLV has been set for this product. As with all industrial materials, exposure of this product to the skin and eyes should be avoided.

SECTION 7- HEALTH INFORMATION

Inhalation hazard is negligible unless heated to produce vapors or as a mist. Vapors or finely misted materials may irritate the mucous membranes and cause irritation, dizziness and nausea.

Eye contact may cause irritation. Irrigate eye with water for at least 15 to 20 minutes. Seek medical attention if symptoms persist.

Prolonged or repeated contact with skin may cause irritation of the hair follicles and block sebaceous glands, causing rash, acne or dermatitis.

Ingestion may irritate the digestive tract; seek medical attention if symptoms persist or if material is ingested in large quantities.

SECTION 8- EMERGENCY AND FIRST AID PROCEDURES

Eyes: Irrigate eyes with a heavy stream of water for at least 15 to 20 minutes.

Skin: Wash exposed areas of the body with soap and water.

Inhalation: Remove from area of exposure, seek medical attention if symptoms persist.

Ingestion: Call physician for advice.

SECTION 9- EMPLOYEE PROTECTION

Respiratory Protection: Respirators approved for organic vapors.

Protective Clothing: Safety glasses, goggles or face shield recommended to protect eyes from mists or splashing. Neoprene or rubber gloves recommended to prevent skin contact.

Other protective Measures: Employees must practice good personal hygiene, washing exposed areas of the skin several times daily and laundering contaminated clothing before re-use.

SECTION 10- ENVIRONMENTAL PROTECTION

Spill Clean-Up Procedures: Remove sources of ignition, contain spill to smallest area possible. Stop leak if possible. Pick up small spills with absorbent materials such as paper towels, "Oil Dry", sand or dirt. Recover large spills for salvage or disposal. Wash hard surfaces with safety solvent or detergent to remove remaining oil film. Follow local, state and federal disposal regulations.

Environmental Hazards: None

SECTION 11- SPECIAL PRECAUTIONS

Store in closed containers below 120o F.

Keep away from oxidizing agents, excessive heat and ignition sources.

Store and use in well-ventilated areas.

Do not store or use near heat, sparks, or flame; store out of sun.

Do not puncture, drag or slide this container.

Drum is not a pressure vessel.

SECTION 12- TRANSPORTATION REQUIREMENTS

Dot Shipping Name: Vegetable Oil DOT I.D. Number: 145100

DOT Classification: Class 65 UN Hazard Class: n/a

SECTION 13- DATE

Date of Preparation: June 1, 1995

Date of Correction: December 2, 2007

Reason for change: Confirmation of updated information.

This information relates only to the specific material designated and may not be valid for such material used in combination with any other materials or in any other process. Such information is to the best of the company’s knowledge and believed to be accurate and reliable as of the date indicated. However, no representation, warranty or guarantee of any kind, express or implied, is made as to its accuracy, reliability or completeness and we assume no responsibility for any loss, damage or expense, direct or consequential, arising out of use. It is the user’s responsibility to satisfy himself as to the suitableness and completeness of such information for his own particular use.