|
||||||
|
||||||
Mer*Lube is a division of JJ Merlin Systems which specializes in Lubricants and Lubricating Equipment. The Mer*Lube lubricants' are of the highest technology and are all environmentally safe. Our abrasive segments will allow you to fully utilize the capacity of your vertical spindle grinder. Our grinding wheel segments cut faster, generate less heat, hold form, produce heavy stock removal rates, and give desirable finishes.
Lubricants acculube trico solid paste
Merlube merlin systec segments grinding
Wheel abrasives stones machining industrial
Mer*Tap SAFETY DATA SHEET
liquids, lubricants, merlin, jjmerlin, merlin, mertap, metal cutting, cutting tools, lubricant, safety data sheet.
|
|
|
Mer*Lube Div., J.J. Merlin Systems, Inc. MSDS Sheet for MerLube829 |
|
Lubricants - 317 | 422 | 517 | 829 | 918 | 962 | 1110 | 1200 (Acclaim) | Slick Stix
MSDS Sheets - 317 | 422 | 517 | 829 | 918 | 962 | 1110 | 1200 | Slick Stix
Equipment | Online Sales | Online Distribution | Helpful Info | JJ Merlin Homepage | Corporate Profile |
|
MATERIAL SAFETY DATA SHEET (MSDS) · Health: 0 · Fire: 1 · Reactivity: 0 · SECTION 1- MATERIAL IDENTIFICATIONMaterial / Trade Name: Mer*Lube 829 Emergency Telephone: 330-798-1800 SECTION 2- INGREDIENTSpecific information is considered a trade secret and is withheld per CER 1910:1200 (h). Medical personnel requiring this information should contact J.J. Merlin Systems with their specific request per CER 101:1200 (h). SECTION 3- PHYSICAL DATA Boiling Point: 540.0-660.0 F @ 760 mmHg Physical Form: homogeneous solution Specific Gravity: .840 @ 77.0 F Solubility in H2 O, % by Volume: Insoluble Vapor Pressure: n/a Evaporation Rate: n/a Vapor Density: n/a Percent Volatiles: no data Color and Odor: clear, L color 1Y/O.1R; pH: 6-7 Liquid Density: 6.990 lbs/gal @ 77.0 F SECTION 4- FIRE AND EXPLOSION DATA Flash Point (Method Used): 200o F PMCC Flammability Limits: n/a Extinguishing Media: Dry Chemical, foam, water spray (fog). Unusual Fire Explosion Hazards: None SECTION 5- REACTIVITY DATA Stability Hazardous Polymerization__X__ Stable ____ Unstable ____ May Occur __X__ Will Not Occur Conditions and Materials to Avoid: Strong oxidizing agents. Hazardous Decomposition Products: n/a SECTION 6- OCCUPATIONAL EXPOSURE LIMITS No exposure limits have been set for this product. As with all industrial materials, exposure of this product to the skin and eyes should be avoided. SECTION 7- HEALTH INFORMATION Eye irritation: non-irritating. Skin irritation: FHSA Rating: not a primary skin irritant; Index 1.3 Oral toxicity: (FHSA & OSHA Rating) non-toxic LD50 (8%-20% solutions); >10gm/kg This product (or components, if a mixture) is not listed in IRAC Monographs, the NPT Sixth Annual Report or the ACGIH TLV’s as a carcinogen or potential carcinogen. It is not regulated by OSHA as a carcinogen.
SECTION 8- EMERGENCY AND FIRST AID PROCEDURES Eyes: Flush with large amounts of water, lifting upper and lower lids occasionally. Skin: Wash exposed areas of the body with soap and water. Inhalation: Remove from area of exposure, seek medical attention if symptoms persist. Ingestion: Immediately drink two large glasses of water; call a physician. SECTION 9- EMPLOYEE PROTECTION Respiratory Protection: Not required under normal conditions of use. Protective Clothing: Safety glasses, goggles or face shield recommended to protect eyes from mists or splashing. Neoprene or rubber gloves recommended to prevent skin contact. Other protective Measures: Employees must practice good personal hygiene, washing exposed areas of the skin and laundering contaminated clothing. SECTION 10- ENVIRONMENTAL PROTECTION
Spill Clean-Up Procedures: Remove sources of ignition, contain spill to smallest area possible. Stop leak if possible. Pick up small spills with absorbent materials such as paper towels, "Oil Dry", sand or dirt. Recover large spills for salvage or disposal. Wash hard surfaces with safety solvent or detergent to remove remaining oil film. Follow local, state and federal disposal regulations. SECTION 11- SPECIAL PRECAUTIONS Store in closed containers below 120o F. Keep away from oxidizing agents, excessive heat and ignition sources. Store and use in well-ventilated areas. Do not store or use near heat, sparks, or flame; store out of sun. Do not puncture, drag or slide this container. Drum is not a pressure vessel.
SECTION 12- TRANSPORTATION REQUIREMENTS DOT Classification: Class 65 DOT Info- 49CFR 172.101: Not regulated by DOT NOS Component: none RQ (Reportable Quantity) 49 VFR 172.101: n/a SECTION 13- REGULATORY INFORMATION
SARA 302 Components- 40 CFR 355 Appendix A: none California Proposition 65: none SARA 313 Components- 40 CFR 372.65: none CERCLA RQ-40 CFR 302.4: none SECTION 14- DATE Date of Preparation: November 1, 1995 Date of Correction: July 30, 2005 Reason for change: Confirmation of updated information. Format presentation.
This information relates only to the specific material designated and may not be valid for such material used in combination with any other materials or in any other process. Such information is to the best of the company’s knowledge and believed to be accurate and reliable as of the date indicated. However, no representation, warranty or guarantee of any kind, express or implied, is made as to its accuracy, reliability or completeness and we assume no responsibility for any loss, damage or expense, direct or consequential, arising out of use. It is the user’s responsibility to satisfy himself as to the suitableness and completeness of such information for his own particular use. |
er*Lube 829 SAFETY DATA SHEET
liquids, lubricants, merlin, jjmerlin, merlin, lube, merlube 829, metal cutting, cutting tools, lubricant, safety data sheet.
